Search Results for ‘tubing’

Passat 1.8T 2000. I have several tubes, covers, a heat shield laying on the ground right now trying to get to something I can clean. I was dumb and was trying to paint my front grill badge with the grill still on. Even though I taped everything up and stuffed the holes in between the badge...

I have the typical plugged heater core in my 02 V6. When i took the large black plastic cover off on top of battery, i found this piece of clear tubing wedged between battery and heater tubing. It has a black plastic 90 deg elbow and an open end that looks like it has a black marking on it. I...

I feel dumb for asking :( I had the ABS module failure a month ago, sent it to guy on ebay who charged me US$ 45 for the fix and today I got my repaired module by mail, works pretty good! That's the sweet part of the story :D Now, since there's ALWAYS a but, when I removed the windshield...

Here's a kit to replace the PCV valve and tubing for a 2003 V6: Volkswagen Passat B5 FWD V6 30v > Engine > Emission > PCV > ES#2090780 PCV Service Kit - Stage 1 - 3B0198007 Two questions: 1) Aside from the PCV valve itself, are the rest of these fittings just tubing, or are there some other...

I've just completed a two day slog (okay, I know, slow, right?) through a valve cover gasket / cam seal / timing belt job on my 2001.5 V6. My wrap-up steps were to replace the breather hoses / suction pump / PCV valve / etc. The whole Blauparts kit. I got that bugger of a hose off from under the...

Replacing my valve cover due to leak...I started this before finding out about the pvc system possibly being the cause from other posts..So, I need to purchase the pvc tubing that runs from one cylinder bank to another since I just broke it. Whats the best temp. fix for this? Electrical tape...

I been working on VDO boost gauge installation for a while. I thought I have all the stuff nailed down until I am ready to connect the nylon tubing to the vacuum line at intake. How do I connect the nylon tube to the plastic T fitting here? the brass connector in the kit is good for...

A good friend has a 2000 1.8T FWD thats having some issues. i got a call about a week ago saying she got a oil pres warning, and a message saying stop engine immediatly. so i had her check the oil, there was none (it had been about a month since she had checked it)i told her to get someone to...

I've tried several online vw parts retailers but can't find anyone selling the pcv valve and tubing set for my B5. Any suggestions?

Finally got my belly pan ready to install. IN the process, found out that the hoses for my SAIP were disconnected. The pump was full of water, cant be too good. I see where one hose goes from the pump to the air box. Theres another hose that comes out of the pump but Im not sure where it...

I've purchased a digital boost gauge that was originally developed for a Volvo, so I need to confirm that the parts will work on a VW. What's in question is the the size of the T fitting and tubing running from the T fitting to the gauge. First, are sizes described as inside diameter (ID) or...

How mny feet of silicon tubing so I need to replace the 4 vacuum lines from the SAI?

Is the intake tubing between the V6 and 1.8t similar. I need the part that attaches to the grill and someone is selling the same peice but it is from a V6. Thank you in advance. Dameon

Yesterday, I started to install a VDO Vision boost gauge from 42DraftDesigns. I ran into an obstacle right from the start - I couldn't get the tubing to fit over the barb on the T that splices into the vacuum hose. 42DD's tubing is a fairly stiff plastic and doesn't have the elasticity to...

is this a good idea, or am i crazy as usual? that way, we can use it for the clearance issues with tiptronics....hmmm? :crazy: i would think it a good idea, because you can make it easier to clear smaller areas like the tranny. And you can easily make the ends round for connecting.. but...

Ok I emailed Hoes techniques about availabilty of a kit for our passats. and there reply was Now if there email was to suddenly become flooded with requests(hint, hint hint, hint, hint) they migh speed up development. The email adrress is [email protected] Understand this would be...

hi guys- do i need to get a tubing kit for a boost gauge (vdo 150-121) or can i use silicone hosing - do i need to really get the kit- does it have fittings i need to install