Search Results for ‘square’

I was planning to change my transmission oil today and got the fill plug off easy, but when it came to the drain plug it was all rusted up and stripped from only a couple of attempts. I already have a new drain plug coming in, so what is my best course of action for getting the old one off? One...

I am doing a CV axle replacement and have read all the forum posts and write ups on this. I am very clear on the procedure, but am just having a sticking point with a triple square bolt on the axle flange. It's the last bolt I need to remove to remove the axle. I have sprayed all the axle flange...

I am doing a CV axle replacement and have read all the forum posts and write ups on this. I am very clear on the procedure, but am just having a sticking point with a triple square bolt on the axle flange. It's the last bolt I need to remove to remove the axle. I have sprayed all the axle...

Looking for 4 5x112 10mm for my b5 Passat I'm located in Nazareth,PA And if you can post pic with price or DM me Thanks Sent from my iPhone using Tapatalk

This weekend a friend and I dropped the transmission out of my car to do a clutch replacement. Fortunately he had a cheap set of triple square driver bits to get the front axles disconnected. We would both like a better set of these for future work. I would prefer something US made but I...

Who is running 18x9.5 and what off set are you using? looking to go from 18x7.5 w/ 225/40 to 18x9.5 w/ 235/40r18. looking to raise front make 235/40r18 to fit.

hey everybody. ive got a few questions. i have a 99 passat with a v6 and 5 speed manual trans. the outer cv joint is going bad. ive purchased a new joint, but im having trouble finding the (6) triple square bolts that connect the cv joint to the flange, which need to be replaced when i take the...

hey everybody. ive got a few questions. i have a 99 passat with a v6 and 5 speed manual trans. the outer cv joint is going bad. ive purchased a new joint, but im having trouble finding the (6) triple square bolts that connect the cv joint to the flange, which need to be replaced when i take the...

I'd prefer the metal hoop at the bottom, are these cross compatible? Will the chip fit or can I program a new SQUARE one to work alongside my original OVAL ones?

Taking a new direction on this. I'll take old, worn out remotes. I just need to recover the circuit board inside. Need two.

Hey all, I just want to make sure before I flush my 5 speed manual what tool I need. I know I need the 12-point but what size? On Ebay they are selling several ones and one hansautoparts they sell 8 ones (just for 3 bucks each). The sizes are indicated with an M and a number. Which size do I...

The ultimate VW enthusiast get-together in the northeast! time to sign up, guys...

For any of you out there that are as stupid as me and think you can get by without a triple square when it's called for. This is one of the screws the holds the rear lock module to the door. One bolt came out with a 6mm allen, but this one didn't. Needless to say, I had to dremel slots in...

Hi, i have a 2002 passat 1.8t, and the little red square on my dash that tells you the gear and stuff, is dim around the outside edges and some times its full and bright. and some times it is completely black.. its not a huge deal but i prefer everything on my car work good. any ideas, or anyone...

What tool or how should I cut out a small square to put a switch in the cubbie out of a b5.5 passat. Its right below the steering wheel on your left hand side. I need to put a small rocker switch there and already have the dash down. Will a box cutter work? What tool will cut plastic

so ive been trying to get my driveaxle out for 2 weeks now, the triple square bolts are very difficult to remove for whatever reason, its the front driver side so im pulling to the left/front of the car, for whatever reason do these bolts loosen the opposite way?