I am rebuilding the heads due to bent valves, and need a few torque specs. My head bolts are the T30, Non-stretch. Dont know if that makes a difference.
I search this forum and googled but I haven't found the torque specs for my 2004 Passat GLX V6 2.8 FWD- Front Driver's CV Axle.
I bought new bolts for the inner and a new 17mm bolt for the outer and I'd want to torque them down correctly.
What I found this far in existing posts was...
I've been a member since 2015. For some reason I am only able to post in Noob Tube and not in the b5 forum for questions I need answers too. What gives? :banghead: I need torque specs for 04 GLX v6, transmission mounts and the 3 hexbolts that mount the bracket to the side of the transmission...
Hey everyone, I've been looking but haven't found the right specs for my engine. I need torque specs for pretty much every aspect of my turbo, manifold, oil lines, etc. also what the specs are when bolting the downpipe back on and the trans to the engine and the mounts. I can't find anything...
I need to change out my OE Sway Bar Links. 100000km and this is the 3rd set going on the car. Warranty is now over so going to save the labor but need the torque spec for these. I searched the forum and can't seem to find many torque specs for the B7 Passat. A torque spec sticky for...
I'm in the midst of my first timing belt job and I'me replacing the timing belt tensioner and idler roller. The tensioner's package contained a sticker which said "Caution: Strongly recommended bolt torque Specification: 25 Nm." I looked in the Bentley for the VW recommended torque spec but...
Model: Passat 1.8
Car Category: Family cars
Car Engine position: Front
Car Engine: 1781 ccm (108,14 cubic inches)
Car Engine type: in-line, 4-cyl
Car Valves per cylinder: 5
Car Max power: 150.00 PS (109,45 kW or 147,26 HP) at 5500 Rev. per min.
Car Max torque: 241.01...
I've been searching till my eyes bleed here and on the net. In search of a good reference of torque specs for B6 Passats. Tons of info for B5's but I'm striking out for B6.
Most specifically I currently need axle bolt torque, inner axle bolt torque, control arm, caliper etc.
As you know, these cars use a bunch of relays, sometimes with part numbers which differ from Bentley or from the next car. If I had a spreadsheet of relay types, including part number (either the 3-digit code printed on the top or the full manufacturer number), coil impedance, and contact switch...
I am putting main and rod bearings in my 2002 1.8T AWM motor. I have been unable to find consistent torque specs on a couple different items, when I searched here I could not find any threads regarding internal engine torques. Here are the specs I found up to 2001 (Assuming ATW...
Hi Guys, I have a 1999 1.8T B5 Passat.
I wanted some help with wheel specs…
I know the stock specs are, 37 offset (or 36) 5x112 bolt pattern and 6.5x16. I wanted to know what other wheels with different specs can fit on my car?
I recently had to replace my transmission range sensor, aka neutral safety switch, aka multifunction switch (MFS), to fix my 2003 Passat's limp mode problems. I have a thread in this forum (it's long) about tracking down the problem and if you're interested you can find it here:
Working on my 06 2.0T FSI, rebuilding the head. I need some torque specs if someone was nice to post them here for future inquires please
1. Head to block bolts
2. head to exhaust
3. head to intake
4. valve cover to head
5. cam sprocket to cam
6. number of teeth on the cam chain between 2...
I just got my kit in from Blauparts to change the timing belt on my new to me 06 Passat 2.0. It has the stretch bolts for the motor mount but nowhere on the instructions that came with it or torque values for the motor mount bolts or the six pulley bolts. Was looking to purchase a Bentley for...
i am currently looking at set of wheel with these specs. Please let me know if they will fit my passat b 5.5 wagon
front 18x9.5 et 12 or 22
rear 18.10.5 et 15 or 22
i dont mind if i have to run spacers to make them fit and i dont mind a bit of poke. i can live with about 10mm of poke in the...