Volkswagen Passat Forum banner

screw

  1. Volkswagen Passat B5 Discussion
    Hello PassatWorld! It has been a while and I'm putting my B5 back on the road. I was hoping that someone would be able to help shed some light on the headlight mounting hardware for our B5s. I was able to find the B5 headlight screw (N90732301) while searching through the VW parts website. I...
  2. B5 Garage
    2003 1.8T wagon. I am replacing my drivers door latch mechanism for the second time. I have also replaced the window regulator. Of course the door clips are breaking and I purchased replacements. My problem is the plastic inserts on the bottom of the door to which the two torq screws attach...
  3. Volkswagen Passat B5 Discussion
    01 V6 2 questions My brother accidently stripped the hex insert to the coolant bleeder screw closest to the front of the motor :thumbdown Do I have to be able to use this particular bleeder point so long as I bleed from the other (the one closer to the firewall) and the one on the heater...
  4. Volkswagen Passat B5 Discussion
    I'm flushing the coolant on my 02 B5.5 1.8t AWM (I think it's the AWM at least) and after draining from the radiator drain valve, I'm now looking for an elusive drain plug on/near the water pump or thermostat. My Chilton manual has a photo from underneath the block that shows a 19 hex nut on...
  5. Volkswagen Passat B5 Discussion
    :lol: But seriously, I am trying to find the part number for the plastic anchor points that the 2 screws that hold the bottom of the drivers interior panel to the door go into. If they are out they are white and squarish. Any ideas....
  6. Volkswagen Passat B5 Discussion
    Hey guys, I was doing my brake job earlier.. Replaced the rotors and calipers... And I found this during the process.. Like the title said, I didn't see any screw to retain the rotor on both sides. And apperently there is actually no place for that at all... Seems like the rotor is hold by 5...
  7. Volkswagen Passat B5 Discussion
    Hi Forum I noticed that I cannot remove wheel because one screw is special and I don't have jack for it. Do you know what is the name of the jack to remove that secret screw, it;'s protection from wheel theft I think So do you know the name to search in ebay?
  8. Volkswagen Passat B5 Discussion
    I recently purchased a 1999 Volkswagen Passat Station Wagon (1.8L). The issue i'm having is with all 3 door locks on the vehicle -- driver, passenger, and trunk. The keys i use to start the car does not fully enter the lock cylinder of the three external locks -- it enters about 1cm then stops...
  9. Volkswagen Passat B5 Discussion
    Hi all, I am replacing the CCT. But, I have been trying to remove this one bolt. I did try to use one size larger torx socket and every time I did it got bigger. I really dont want to drill or anything that would scatter metal splinters in to the head. Could you give me some ideas? Thanks.
  10. Volkswagen Passat B5 Discussion
    You won't believe this. my belly pan fell off as i drove over a small speed-bump. i noticed i was missing a few screws, only had two left. so i went to the same stealership who screwed up my oil change to get the screws. they want $5 for each screw. i'm like :crazy: you guys know anywhere i can...
  11. B5 Garage
    after i finally got the alternator wiggled into place, the top alternator bolt won't screw in...it the one that uses the allen wrench. ...it pushes in to the point of resistance where you would use the allen wrench to start screwing it in, but it's like the threads won't catch. ...what's...
  12. B5 Garage
    Hi this is my first post so please let me know if I have omitted any information you need. Sorry it's so long.... Do I need to put my vehicle info in the Title, or just in the body of the post? I have been learning from PW for over a year now and I haven't found this issue in the garage or...
  13. Volkswagen Passat B5 Discussion
    Hey guys, I currently have my front bumper off the :b5: because it's being re-painted. I found this bolt unscrewed and then when I tried to screw it back in, all it does is spin the washer that's on the actual support bracket it's suppose to tighten down. There is no nut on the other end of the...
  14. WTB/WTT Section
    Need a black b5.5 shift knob/boot. Prefferably in good condition. Need the clamp on style though, not screw on.
  15. B5 Garage
    1999 (V) Passat 1.8 SE Petrol. Rear Passenger Door Lock. I've had various electrical problems which I'm trying to solve. Have used this site to check for battery drain, etc etc.... Latest suggestion involves checking the solder points inside the Lock mechanisms, and to do this I need to remove...
  16. Volkswagen Passat B5 Discussion
    Does anyone know what the adjustment screw on the N75 boost control valve is doing? What it actually changes? What the effects are from turning clockwise or counter clockwise? I would like to try to 'de-adjust' my current setup since the combination of larger turbo, N75, wastegate...
  17. Volkswagen Passat B5 Discussion
    Hey guys a couple months ago i bought a used 2003 passat gls. There has not been any problems with the car except for the damn leather! I dont know if the previous didnt use any of the seats but they are literally falling apart on me! I was just wondering what you guys thought as a solution...
  18. Volkswagen Passat B5 Discussion
    02 Passat Low beams needed help. Polishing helped but still a little dim. Installed Sylvania Ultra's and they look a lot brighter. (It's not Night yet so I really can't do a fair comparison.) Heres the "What did I screw up" part. Before the install, start the car and the City lights come on...
  19. B5 Garage
    Hi im trying to remove the screw holding the combi valve but i don't have a short enough wrench to fit in. do i need to buy a special tool? if you look at the picture i can't get my wrench in there because it hits the top.
  20. Volkswagen Passat B5 Discussion
    Alright, I need some help. I picked up a real nice wooden shift knob for my 2004 b5.5 passat. The knob is screw on but the stock setup uses a clip, or a metal ring. I took the clip component out of my stock one, and pretty much destroyed the stock knob. Any ideas on where to go next?
Top