Search Results for ‘p0011’

I had the timing belt replaced on my 2007 2.0t fsi about a month ago. A few days after I got it back, the car started throwing a p000a code. I replaced the n205 valve and now the car is throwing a p0011 code. No noticeable loss of power or rough idle. Any thoughts on where to start looking?

I have a 2001 b5.5 with the 1.8t AWM engine and I just recently replaced my vvt/cam chain tensioner, cam chain, and cam position sensor. A few months ago I replaced the timing belt, belt tensioner, and Water pump. I did the computer reset after and that cleared my CEL, the car fired almost...

My 02 1.8T has started stumbling occasionally while driving. Just a tiny second of rough running once or twice a day. Other than that, the car is running great. It doesn't always illuminate the CEL. First time I scanned the computer I got a P0011, and the next time a P0012. First scan...

Getting both on 01 AWM. Am I looking at replacing the CCT again? Car has 235k on it, with about 55k on CCT.

Hi Everyone, 2003, 1.8t, AWM, 124.000 miles. I got my first CEL last week having driven 11.000 miles since I bought the car. I did a complete TB replacement as soon as I bought the car. I replaced the cam chain adjuster, which I bought from FCP. 16395 - Bank 1: Camshaft A (Intake)...

Hi Folks, I have had this pesky p0011 code for the last couple months. I recently replaced the Cam Chain Tensioner about 3 weekends ago and I just checked again for Codes and it came back p0011 Camshaft Position Timing Over-Advanced Or System Performance Bank 1 I have changed the oil the same...

Hi passatworld. My 04 1.8t AWM has had a p0011 engine code for the last 2-3 months. It sounds like a diesel when it starts and sounds fine when it is warmed up. This morning I tried to start the car and nothing happened. 1 minute later I started it up and it idled rough and shut off in 2-3...

We've owned a 2003 Passat 1.8 AWM for going on 3 years now. Shortly after purchase the CCT exploded allowing the cam chain to eat a few slits in the valve cover. With much sweat, swearing and assistance from this forum I replaced the CCT, dropped the oil pan, cleaned it all out, replaced the oil...

Morning Everyone, new to this forum and just picked up my first passat after selling back our tdi sportwagon. Here is a quick background on the car. 78000 miles, well maintained and had the timing chain tensioner, chain, guides done in late 2014 at 56000 miles with the lastest version...

Hello, I have a 2004 passat 4 cyl with 100k miles and change. Recently got a CEL and got P0011 with my generic code reader. I also noticed a intermittent buzzing noise from the front of the vehicle while on the highway, audible for a moment or two, every couple minutes. Twice when pulling of...

2001 GLS 1.8 Sedan AUG Engine Automatic Transmission. 191,900 miles, October 2015, had Timing Belt Service, all belts Tensioner, Tensioner Roller, Water Pump, Thermostat and the Transmission Oil Pressure Lines – Lower & Upper, replaced. This week at 195,800 miles, after highway driving for an...

2001.5 1.8T with AWM engine got a P0321 with typical symptoms (random stalls). Replaced crankshaft postion sensor and it ran great for a coouple of days. Then suddenly at highway speed, it jerked, hesitated and it has been doing that ever since. Codes are P0011 and P0321 (although I am not sure...

Hello. I'm very new to this forum (3rd post) and I apologize for making another thread about the P0011 code, but mine is doing something odd. I have a 2003 Passat W8 which is giving me a few codes. First and foremost it is the P0011 code. Second is the thermostat (or so I was told), but I'm not...

Ok so i have a cel but didnt scan it till today, i only scanned it because while i was driving the STOP CAR OIL PRESSURE LIGHT came on so i went to AdAuto to get it scanned and it was the p0011 timing advanced code, that would point to the tensioner or is it REALLY low oil pressure or can it be...

Just changed the timing belt and all the other stuff that came with the big kit. Car runs great. A few days after, still running great but CEL came on and did the read on it and it comes up P0011, cam intake timing advanced, something along those lines. I pulled the front end back off and...

I searched but don't have a clear answer to this. What does this mean? Can I still drive the car? No Check engine light. I only found the code because i bought a cheap ebay cable and VCDS Shareware and next to the code it said internment so i guess it didnt actually throw a MIL...yet.. but...

Hi all, I recently purchased a 2008 VW Passat 2.0T 6-speed manual with 107,000 miles on the odometer. Soon after the purchase, the check engine light came on and I noticed a miss on hard acceleration. I had the check engine codes checked out and they were P0011 and P0304. I thought that maybe...

First, I want to assure you that I have searched the B5 garage forum looking for my answers. But for some reason, nothing I search for returns any results. Literally, nothing. So here's the issue: 2004 Passat Wagon, AT, AWM engine. CEL came on today. Code check showed P0011 and a previous...

So I went to the local AutoZone to pick up some oil to add to my car and on the way home my CEL came on. I went back to them and they scanned and gave me code P0011 for the cam shaft. When I got home I added the oil and the light turned off shortly there after. Whenever I would scan my car the...

This is a reoccurring code, it seems like 100-200 miles and it shows up again. I wish I would have written down the extra info, something about deceleration, 1.x% engine load... Anyway, after clearing it, how many miles and starts do I need to go to clear the memory of it from the ECU so it...