Search Results for ‘hex’

I was replacing my valve cover and cam chain tensioner gaskets on my '02 Passat 1.8L GLS and I'm almost 100% sure I dropped a 1" hex bit into what I'm assuming is an oil passageway right under the exhaust camshaft-side of the drive chain. I removed the cam chain tensioner and the intake...

Hi, So I have finally got my immo3 B5.5 FIS cluster :D I have done the key matching, soft coding, distance to empty, welcome message and illuminated needles/dials. The cluster works perfectly :) . However, as it is an immo3 cluster, it contains the VIN of the previous vehicle in the EEPROM...

2000 GLS Wagon 2.8L (ATQ) H6 drive took out seven bolts, just spins in #8. My job to renew gaskets and seals - both sides - is stalled until I can get this out. Any good ideas? I guess I could take out the crankshaft bolt(!) but would rather leave it on (unless I see that the crankshaft seal...

I need help to buy a diagnostics cable for my 2006 passat b6. Any ideas where i can find one a bit cheaper than that at Ross-Tech. Thanks.

Ahh! help please. I ordered this kit from Ecstuning b/c their support rep suggested it and told me they were all the same. http://www.ecstuning.com/Volkswagen-Passat_B5-4_Motion-1.8T/Drivetrain/Axles/CV/ES1478/ But the kit comes with a 27mm hex axle bolt, instead of the 17mm allen bolt that...

1.8 t ATW. I tried and tried no luck. I gave up. Is this bolt absolutey essential??? I had it almost all the way in, but it definitely felt cross threaded so I backed it out. The bracket itself has a lot of bolts holding it down. Someone make me feel better.

I'm replacing the front wheel bearings on my step-son's 2000 Passat 1.8T auto, and the new wheel bearing kits came with axle bolts that have the 17mm hex key head, while those on the car have the 14mm hex key head. Can I use the 17mm hex key head bolts instead? Do I then use the 140ft/lbs...

SOLD SOLD SOLD This is a *USED* GENUINE cable and will work with all future Rosstech software versions. Here is all you need to do to use this cable: 1) Download FREE software here: Ross-Tech: VCDS: Downloads: Current Release and Manual 2) Install software on laptop or PC (that meets the...

Trying to get my alternator out. Went and got the clutch fan removal tool from local auto parts place but the size that its suppposed to be 1 7/8 does not engage it seems to be a solid 1/8 inch too large nowhere near grabbing. The set I got came with many other sizes as well but none of them...

I have a chance to grab a HEX+CAN for a good price. I have a B5.5 2001. Is this going to work like a VagCom? He says it has full VCDS access. Thx for the help.

alright so i am going to replace my turbo with a ko4 and the hex bolt underneath the turbo is striped.i did some searching and the only thing i came up with was to drill the bolt out. just wondering if there is another way or is just drilling it out the easiest way? also do i even need the...

I am looking for input here. Has anyone heard anything about Hex Logic buffing pads and had anyone used them before? Is the quality just as good as the Lake Country pads? Is there a benefit with the "hexagon" shapes in the pad? The only thing I can tell from looking at them would be, a little...

Price reduced. Only used a handful of times. [email protected]

Hi all. New to the site. I joined because my sister in law has a 02 with AWM engine and we did the timing belt the other day. I have a 98 Jetta TDI and my wife has an 11 Jetta TDI. For my birthday they chipped in and got me a Ross-Tech cable. If you're near Elkton, MD/DE state line and need...

$250 OBO. [email protected] Buyer pays shipping.

Sold

anyone know what size hex or triple square i need for the oil drain plug? idk why but mine is not the regular 19mm. thx