Search Results for ‘g28’

Hello! So I removed the engine to replace the timing chains and some gaskets, etc. Now when I have put it back, it won't start anymore. VCDS says 00513 - Engine speed sensor (G28) 03-00 - No signal. Ok, seems pretty simple - replaced the sensor. Nothing changed. Checked the wiring - everything...

Hello all, my 07 passat wagon 2.0t has been experiencing an abrupt bog when engine speed hits 3000 rpm. the car has no other issues and once it does it it won't reoccur until the car is shut off and restarted. also causes the car to idle around 1000 rpm until restart. i scanned and got a p0321...

<edit> Actually think this is called the Crank position sensor or Engine Speed Sensor) I am having a heck of a time finding any resources or information for this engine. In particular, I have all the classic symptoms of a bad CPS including the codes for intermittent failure 16706/P0322. I...

Hi all, I hope you can help me with a bit of diagnosis. My 2.3 v5 Passat (B5.5) is throwing out the following error via VAG COM: 17755 - Camshaft Position Sensor 2 (G163) / Engine Speed Sensor (G28): Incor. Correl. P1347 According to the VAG Wiki this is due to one of three things: 1) Duff...

EPC light came on a few times randomly over the last few months - but this past week it comes on after about a 20 minute drive and the cars runs like garbage. Pulled codes, G28 Engine Speed/Crank sensor fault. Replaced, honestly a piece of cake IMO. But upon starting up and clearing code...

Hello fellas! Can the "17748/P1340/001 - Camshaft Position Sensor (G40) / Engine Speed Sensor (G28): Incor. Correlation" issue be fixed without removing the whole front end. Passat 1.8T, Runs fine but it throws this code! (no other codes!) im suspecting the chain is off 1 link i counted 15...

Hi woundering if someone could clear up a problem I hav , I took my car to be because it wouldn't start up and kept saying engine fault. They told me it was a g28 engine speed sensor my problem is when I look in to buying a part or try find a diagram with the location of this sensor people...

my car is a 02 1.8t with 126xx recently i had the low oil pressure light with the loud timing chain tensioner tick so i replaced the clogged oil pick up tube cleaned the pan and went to start the car and nothing, it just turns and turns but doesnt want to fire up. everything is good now, the...

17605 engine speed sensor G28 implausible signal. i just had this fixed today after going through hell, the car take 6 to 7 seconds to start up, it come up with g28 sensor signal , i have changed the ECU and it did not solve the problem i also changed the speed sensor original from vw , no...

Hey guys, I have searched on here for 3 days trying to find the exact location of the G28 (crank/engine speed sensor). I have gotten the intermintant starting issue where it will randomly turn and turn and turn, but won't start. Then, after anywhere from 10-30 minutes later, it will start but...

Hi Everyone, My 1998 V6 30V 2.8L Automatic/tiptronic Passat with an ACK model engine randomly does not start and also randomly stalls while driving. I pulled the code P0322 -35 - 10 Intermittent / 16706 - Engine Speed Sensor (G28) No signal or Intermittent. I have the Bentley but annoyingly...

I get an 8 volt PP sine wave, is this the correct output?

So I think I just about completely ragged out my k03. Only boosting up to 5psi. So I've been considering many turbo options here. The ball bearing ATP's sound pretty cool, and I see I should do a fuel regulator upgrade along with further chip tuning. All though,, since I don't know anyone with...

A while ago I started noticing that my beloved B5.5 seemed to give me trouble when starting every so often. Never when cold, but often after driving to a location shut off and attempt to start. Normally not a big deal because it often starts on the second of third try. Saturday I was on a busy...

Hello, I have a 99 aeb 5 speed. Car has been down for a few months because it would not crank and had a G28 Engine RPM sensor code. Finally replaced sensor and now it will crank but won't start. Code still comes back after I clear it though. I put new plugs to make sure it wasn't flooded. I am...

Hello, I have a 99 aeb 5 speed. Car has been down for a few months because it would not crank and had a G28 Engine RPM sensor code. Finally replaced sensor and now it will crank but won't start. Code still comes back after I clear it though. I put new plugs to make sure it wasn't flooded. I am...