Search Results for ‘crankshaft’

Needing a bit of help, occasionally on a warm day especially my car will take a while to start, and now a few times doing any speed when i have took foot off accelerator and applied brake the engine has just died and battery light comes on but it always so far has always restarted straight away...

I am thinking of doing a leak down test due to low compression pressure the test requires getting the piston of the cylinder under test to TDC in compression stroke, which is usually accomplished by tuning crankshaft bolt (on Tiptronic tranny). On 1.8T B5, crankshaft doesn't seem to be...

Now at 196,000 miles and looking to buy Tools for Timing Belt Replacement for my 2003 Passat B5.5 4Motion V6 Wagon..... :wrench: I FOUND THE SET ON EBAY FOR $75.47 NEW!

does anyone know the easiest way to change the swan neck crankshaft breather hose on the 99 passat please no room to move!!!

Im going to replace the dualmassflywheel and the clutch.Once the gearbox is down i thinked to change the Crankshaft Seal.Can i start the engine after changing the Seal or i have to wait for hours?Do i loose engine oil when changing the seal? Thanks

This is my first VW, made the mistake of buying it from a dealer that had zero service history on it. After my first oil change, I put in 5W40 Castrol Syntec, it started leaking oil. Wasn't leaking previous to the oil change. The oil that came out was black and nasty and definitely not...

I have an ATQ 2.8l V6 crankshaft for sale, its in the motor right now, I can have it out fast, Engine is out of car. Looking to get $200 picked up for it. I also have an ATQ Oilpan if you just want it stock $75, if you want me to add an aluminum ski plate to it (tig welded on) it'll be $125...

Is this where it goes? If so where is my old one??? and if so where does the other end clip in?? Is it common for these to fall out? I have been searchin and searching for these answers to no avail. so please help me. It's a 2001 Passat 1.8T AWM

I'm in the dead middle of a timing belt/everyotherbelt replacement, and I'm stuck at trying to get the four bolts that hold the crankshaft pulley cover thing off. I've tried a hex bolt, star key, a triple-square... everything either fits too loosely, or is too big by like .0001 of a cm. I feel...

HI, I have a serious trouble with my Passat. What seemed to be just a pulley became a nightmare when my mechanic opened the frontside and saw that the crankshaft is kaput. He suggested me that it's better to get a second hand engine block then to repair this one. I have this car for 2 years...

I just had my dash out to replace my heater core and installed a new stereo (plug and play). It exploded and burned both the feet of my wife and I. Fun! Not really. I have had the car back together for about a week and today my EPC light comes on and I have no power. I have my crankshaft sensor...

Hi VW World, My name is marko and I' m driving an awesome red B5 passat 1.8t There is a slight ticking sound while the car is on idle so I want to the mechanic today. He lifted her up and stated the engine, and I could see that the pulley is turning very strange. He said if I'm lucky, that...

Hello, I am doing TB replacement and I would like to change seals for Camshaft and Crankshaft. The sprockets are aligned as recommended and then I took the belt off. I know it is lethal to turn the sprockets with TB off, but how can I remove the sprockets without turning them so I replace the...

Recent Timing belt job completed (< 750 miles ago) I'd like to know what the symptoms are for a Crankshaft Pulley that's failing. For example the key on the inside of the pulley is worn. How would the car drive?

Hello. Most of you should know that i'm not from US and english is not my native language. Around a month ago I bought a set of two seals that I thought were the crankshaft ones. Any way, comparing them to the one I had previously bought it's pretty obvious that these parts are not the same...

Hello everyone I am doing a timing belt job on my 04 tip awm engine code. If im not mistaken dont u need to remove the crankshaft pulley to remove the timing belt. I removed the four small bolts inside the pulley but it wont move. So wat do i need to do to remove it.

I am in the midst of changing the time belt and was removing the crankshaft bolt to replace the seal. The crankshaft pulley moved (counter-clockwise). I think that is a pretty bad sign, right? I do have the VAG tool plugged into the crankshaft sealing plug. What should I do? :cry:

While driving home my 2004 Passat 1.8T started to shudder, and as soon as I tried to accelerate, it died. My CEL came on, so I read the code and it looks like a Crankshaft Position Sensor that went out. I have been reading on here that it could also be the fuel pump. I have also read that the...

Does anyone know what the symptoms are for a bad crankshaft position sensor? What about for a bad camshaft position sensor? Is there another name for the crankshaft sensor, I am having a hard time getting a part number out of ETKA? 2001 1.8 AWM

Hi guys, New to the forum and I need help with my passat. I have an 06 passat with the 3.6 and love the car (when its not in the shop). In the past 5 months the EPC light and engine light has come on 4 times now. The dealership is telling me the error code is P0116 which is the crankshaft...