Volkswagen Passat Forum banner

Discussions Showcase Albums Media Media Comments Tags Marketplace

1-11 of 11 Results
  1. Volkswagen Passat B5 Discussion
    2002 V6 ATQ, GLX 4-Motion, auto trans (tiptronic) I replaced the MAF sensor and the Engine Speed Sensor/Crankshaft Position Sensor (CPS) because, while driving, the car would suddenly act as if the ignition was switched off and then quickly back on. That is no longer happening, but now, when...
  2. Volkswagen Passat B5 Discussion
    My 2004 1.8 Wagon is not starting all the time. Sometimes I try to start it and it cranks but does not fire, I stop and try it again and it starts. I checked the codes and it has P0343 showing as a Camshaft Position Sensor A-Bank 1 Circuit High Output. Should I just replace the sensor or could...
  3. B5 Garage
    Hey there everyone, i have used this site for reference forever and have finally decided to join and participate. So ESPN version i have an 2000 1.8t i believe the atw. So i was driving it all day yesterday and everything seemed to be just fine and working normally, one detail i believe i should...
  4. Volkswagen Passat B5 Discussion
    Keep getting the code for the Bank 1 Cam Position Sensor even though I replaced it. I finally got time to investigate and found the new CPS mangled and the impulse rotor bent. Here is the image: So I need to replace the sensor and impulse rotor. I have a couple of questions related to this...
  5. Volkswagen Passat B5 Discussion
    Got whole TB changed with pulleys and water pump at local VW dealer. After 35miles valves met chaos in the head. Dealer stripped down all covers and it turned out that one 10mm bolt that is holding CPS in place came loose and fell in to the TB and ate it and crank pulley teeth. Dealer claims...
  6. Volkswagen Passat B5 Discussion
    Hi all, Newbie here with 04 B5.5 with 1.8T AWM. Love the car, but getting some codes lately. History- bought car new in 04, did all my own oil changes every 5k with Mobil 1 0w-40 since new. Car now has 73k and drives perfect. No clatter, no funny noises, runs as good as new. No engine work...
  7. B5 Garage
    How the heck do you replace the crank shaft position sensor on a v6 b5?? i know where the sensor is and i can see it from under the car, but the wire that goes to it looks like it disappears under the intake manifold when i traced it back? Is there anyone who has replaced one of these before...
  8. Volkswagen Passat B5 Discussion
    Car is a 2001 Passat 1.8T, AUG. I'm researching the difficulty of replacing the camshaft position sensor. The Chilton 1998 - 2001 Passat manual makes it sound difficult - remove upper timing belt cover, timing belt and sprocket, R and R the CPS sensor. But the 1999 - 2005 Haynes manual for...
  9. Volkswagen Passat B5 Discussion
    So my car didn't make it to H20 this yr she wouldn't start... So here's the issue, no start, i'm gettin fuel, i'm getting spark, it cranks, but kinda seems slow, i VAGCOM'd it and no Code's, then i went to live mode, and i'm only showing 200rpm crank speed??? CPS bad? Cam sensor bad?? the only...
  10. B5 Garage
    Is there anything I can do to troubleshoot this code (P1392, Camshaft Pos.Sensor,Bank2 Open Circ./Short to B+) for a 1999 V6? I assume it is either a bad sensor or bad wiring somewhere. Any help would be appreciated. Can someone direct me to the offending sensor? I searched this forum and the...
  11. Volkswagen Passat B5 Discussion
    I just got my car back, and the p/n for the three new CPs I got ends in L...that's 2 generations after the J! Man, they must have had serious issues that they still couldn't work out for a LONG time. Now, the question is, what of the J CP in my car from the first H that blew? Here's the new...
1-11 of 11 Results
Top