Volkswagen Passat Forum banner

Discussions Showcase Albums Media Media Comments Tags Marketplace

21-39 of 440 Results
  1. Volkswagen Passat B5 Discussion
    Hi everyone. I have a 2.8 30v that I was told came out of a 1999 Audi A4 Quattro. I also have a 2.8 30v that I just took out of a 2002 Passat Front Wheel Drive. I am planning on swapping cranks from the Passat to the Audi engine and discovered that they have different connecting rods. The Passat...
  2. Volkswagen Passat B5 Discussion
    So I'm spewing oil out from the rear of my AWM oil pan. The 2 bolts in the rear feel stripped. Probable cause of the leak? You may know of the limited space in that area between the pan and tranny. Too tight to even get a 6/12pt socket on those bolts (allen sockets are my only hope). You think...
  3. Volkswagen Passat B5 Discussion
    I got a great deal on some replacement upper control arms - but - the arms do not come with the replacement bolts and nuts. If I buy them at the dealer they charge about $10 for each bolt and $5 for the nut but they didn't seem sure of which bolts to sell me and wanted me to bring the old bolts...
  4. B5 Garage
    I'd greatly appreciate opinions on this: I've replaced a few axle bolts over the years and generally followed the Bently Manual instructions to torque to 140 ft-lbs and then the additional half turn (180 degrees) after. But I usually would only do an additional 1/4 turn (90 degrees) because I...
  5. B5 Garage
    I need a definitive answer! I'm doing the motor, snub, & trans mounts and recently did the rear lower control arm on my 01.5 ATQ/DVZ, and I'm pretty sure these are what need to be replaced... - motor mount: N-906-630-02 (bolt) - trans mount: N-010-470-7 (bolt) + N-023-004-11 (nut), reusing...
  6. WTB/WTT Section
    Anyone have a B5 V6 engine lifting bracket laying around?? It's not available as a replacement part and has no part #s. I have the one that came on the front Drivers side, but there isn't one on the rear of the Passenger side head. It's the same part for both locations. There is on for sale on...
  7. Volkswagen Passat B5 Discussion
    I was replacing my ABS control Module yesterday and when I pulled the wheel liner back I noticed something that looked like it was missing a bolt I attached apicture of the passenger side as its missing on both sides. It looks like the subframe goes into it or something. Anyways I had my...
  8. Volkswagen Passat B5 Discussion
    So, what's the best practice with the captive "soft" steel crush washers on the banjo bolt if you have to crack 'em to do any work on the calipers? Snip 'em off and use copper crushers, or what do you recommend? I'm replacing my calipers with some rebuilts I got on Amazon. The bottom steel...
  9. B5 Garage
    So what's the best practice on the banjo bolts with the "kept" soft steel washers if you have to crack them to do any caliper work? Clip off the steel and use the copper crushers?
  10. Volkswagen Passat B5 Discussion
    01 Passat Is Locktite recommended on the 6 bolts that attach the inner part of the Axle under the heat shield? If so what color? Thank you
  11. Volkswagen Passat B5 Discussion
    2001 Passat V6 2.8 4 Motion Does anyone have a diagram or any information that would show and/or tell information on the 4 throttle Body bolts? I've picked up from bits of info here and there that one of the 4 bolts is a different size? 3 or them have a 5mm Allen head?, and the 4th one...
  12. Parts For Sale
    2 ECS 15mm spacers w/ 10 ball seat bolts + 2 H&R 15mm spacers w/ 10 ball seat bolts 2 ECS 15mm 5x112/100 57.1 hubcentric spacers with 10 ball seat bolts - $50/$60 shipped 2 H&R 15mm 5x112/100 57.1 hubcentric spacers with 10 ball seat bolts - $60/$70 shipped 20160118_170118 by MoravianFluke, on...
  13. Parts For Sale
    FS: NIB (20) OE Passat B5 'Cone Seat' Wheel Bolts These 20 top shelf cone seat bolts are used on aftermarket rims and are OE standard length. $20 shipped
  14. Parts For Sale
    Part# ECS 1072CSLVR, purchased from ECS for my 2001 1.8T (AUG) but never installed. (may fit others) $130 + ship.
  15. B5 Garage
    Does anyone know the recommended torque spec for the mounting bolts? Thanks :-)
  16. B5 Garage
    I need to replace the coolant flange on the rear of the head. This is on an 01 1.8t AWM car. Has anyone removed the 2 transmission mount bolts and lifted the rear of the trans to allow easier access to this flange? I do have the car in "Service mode" so I don't have to worry about hitting...
  17. New Member Introductions
    I need to change the dreaded coolant flange on an 01 Passat AWM. Has anyone removed the transmission mount bolts & jacked the rear of the tranny up to give more access to the rear of the head?
  18. Volkswagen Passat B5 Discussion
    My driver's axle is due for re-booting and I pulled it today to send off to Marty. I have a decent-quality 3/8" 10 mm triple-square, the splines were clean, and I know they were torqued correctly. Nevertheless, I very nearly stripped the splines of the first bolt. With some P'Blaster and...
21-39 of 440 Results
Top