Hi everyone. So for the fast couple of months I've been having power issues on my Passat 1.9TDI 2006. After a couple of hours the power completely draws out and then I have to charge the battery. I've dealt with this by taking of one of the battery terminal connectors after I get home or to my...
I activated my XM radio and only Channel was working. When I called to activate my satellite option it grayed out the option for my XM selection. It now says that I need to replace my satellite module??? Sirius XM folks are saying this.... This is $600.... Can I transfer the module from a GMC...
Hello, I am new to this forum and have looked high and low for a pic or video on how to remove the HPFP on my 2006 Passat VR6. I have found several 2.0L how-tos but nothing on the 3.6 I need to change my cam follower ASAP.
I have 2 codes that might be related (from other posters/forums):
008328 - Bank 1 Camshaft A (Intake) Position Actuator
P2088 - 002 - Short to Ground
001681 - Fan 1 Control Circuit
P0691 - 002 - Short to GND
I need the wiring diagrams (2006 Passat 2.0T auto FWD, BPY engine) for both...
I have a Service in 5400 miles or 15 days info that comes on during car start?
What would I have to do to clear it or what do you think it is referencing to?
Mileage is currently at 116,496 miles. I'm not within the oil change schedule.
Fairfield, CA :wrench:
Please i need your help here. My ECU got damaged with water, this was due to blockage of the water drains. However since then i have tried a few used ECU's with the same number but the car never starts. it tells me ''Immobilizer Activated'' i still got another that has the same number...
I had the intake of my BPY engine (carbon build up cleaning, timing belt, cam chain/tensioner, vac pump seals, etc).
3 injectors came out (cyl 1-3), on stayed in head.
After installing intake, gas is gushing out (and engine not starting) from under the intake (not exactly located).
Hello everyone ,
so my passat b6 bpy engined failed , so i decided to embark in a project on rebuilding the engine, but
honestly it was to costly, what i ended up doing got a 08 audi with a bwt engine on it . anyhow
with the help of some mechanics, we swapped the engine and bolted right in...
Ordered passenger CV axle (aftermarket).
Length seems to be the same, but the OEM appears to be bigger diameter and hollow, vs. the new is small, solid.
Should i use it?
Need to replace both CV axles of my 2006 Passat 2.0T FWD.
Pulled both axles, but the 'cup' stays on the tranny.
Is it held by a spring clip and needs to be 'yanked' out?
The flex pipe (back of engine) is broken.
While cheap downpipes are available for other 2.0T (recently bought one for my 2006 A3 FWD 2.0T), i can't find a reasonable (i.e. cheap) downpipe listed for the 2006 Passat 2.0T. Or I am not looking for the right model. Is the there a model that cross...
How can I remove the chrome trim off the front and rear bumper?
I need to prepare the bumpers for a fresh paint; clear coat peeling (seems to be a common issue on the VW and Audi I own/owned of that generation).
Also: the "build" sticker (normally in the trunk; spare tire well?) is missing...
In order to replace the door actuator is it necessary to drill out any of the rivets on sub-panel? Or is it even necessary to remove the sub-panel in order to replace door actuator (drivers side front door)? I ask this because when I got car back from mechanic that replaced door actuator the...