p1392 and p1626

+ Reply to Thread
Results 1 to 5 of 5

Thread: p1392 and p1626

  1. #1
    Neutral
    Join Date
    Dec 2009
    Location
    Tulsa, OK
    Posts
    103

    p1392 and p1626

    99 passat GLS V6 2.8l 5 speed manual. These codes come on as a pair at the same time. Sometimes a p0300 and other 3 misfire codes (forgot which ones but it don't really matter). Sometimes it takes a lil drive for these codes to come on but usually they pop up right at engine start. What is the problem? Why do I have transmission control unit code if I have a manual transmission? Which side is bank 1 and which side is bank 2 if I have to replace the camshaft position sensor? And last question: What symptoms would I have if the engine had a misplaced timing belt by a tooth, or/and a misplaced cam chain by a tooth? I recently did the valve job on this engine. First engine I actually rebuilt myself, don't have mu ch experience, so I think i might have misplaced something there, but the car runs really good. Lotsa power and good gas mileage. Any help?

  2. Remove Advertisements
    VW Passat Forum
    Advertisements
     

  3. #2
    Neutral
    Join Date
    Dec 2009
    Location
    Tulsa, OK
    Posts
    103
    No clues

  4. #3
    1st Gear
    Join Date
    Jul 2008
    Location
    Neenah, WI
    Age
    31
    Posts
    227
    17800/P1392/005010 - Camshaft Position Sensor Bank 2 (G163): Open Short to Plus
    Possible Symptoms

    * Power Loss at Full Throttle
    * High Fuel Consumption
    * Bad Emission Values

    Possible Causes

    * Wiring between Engine Control Module and Camshaft Position Sensor Bank 2 (G163) faulty
    * Power Supply/Ground Wiring from/to Camshaft Position Sensor Bank 2 (G163) faulty
    * Camshaft Position Sensor Bank 2 (G163) faulty
    * Engine Control Module faulty

    Possible Solutions

    * Check Wiring between Engine Control Module and Camshaft Position Sensor Bank 2 (G163)
    * Power Supply/Ground Wiring from/to Camshaft Position Sensor Bank 2 (G163) faulty
    * Check Camshaft Position Sensor Bank 2 (G163)
    * Check Engine Control Module

    P1626 Data Bus Powertrain missing message from Transm.Contr.
    ... sorry not sure what this one means... could it be that a problem with your ECU is causing this one too?

  5. #4
    1st Gear
    Join Date
    Feb 2010
    Location
    Chicago
    Posts
    193
    you shouldnt have a TCM (Tranmission Control Module) if your car is a 5 speed. Recode the ECM so that it won't look for it.

  6. #5
    Neutral
    Join Date
    Dec 2009
    Location
    Tulsa, OK
    Posts
    103
    It was a misplaced cam chain by a tooth.

  7. Remove Advertisements
    VW Passat Forum
    Advertisements
     

Quick Reply Quick Reply

Register Now

Please enter the name by which you would like to log-in and be known on this site.
If you do not want to register, fill this field only and the name will be used as user name for your post.

Please enter a password for your user account. Note that passwords are case-sensitive.

Please enter a valid email address for yourself.

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.


Thread Information

Users Browsing this Thread

There are currently 1 users browsing this thread. (0 members and 1 guests)

Tags for this Thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
Powered by vBadvanced CMPS v4.1.2